| |
| Monitor Mounts |
| |
 |
Open LCD Monitor
Mount
This is a simple mount that lowers the monitor into the
desktop to reduce its visual impact. The monitor angle and
direction can be adjusted normally. Generally this mount is
not model specific and will accommodate most monitors.
However it is best if we have the monitor or at least a cut
sheet before construction because the variation in
dimensions between models is very wide. |
| |
|
M-MON-L Open LCD
Monitor Mount |
$500 |
|
|
 |
 |
|
|
Surface Mount
for Large LCD Control Panels
Larger LCD control monitors designed to be mounted on walls,
like the Crestron shown, are often too large to simply mount
in the control panel of a lectern. The work surface must be
cut away to allow for proper line of sight to the bottom of
the monitor. The larger the monitor, the more desktop is cut
away.
|
| |
|
M-LCD-SM Large
Control Panel Monitor Mount |
$650 |
|
|
|
|
|
|
Recessed Monitor
Mount with Locking Cover
A locking frame with plexiglass controls access to LCD
monitors. Includes recessed base construction.
|
| |
|
M-LCD-S Security Cover
Mount |
$990 |
|
|
|
|
|
|
Open Recessed LCD
Monitor Mount
This is a complex mount that must be hand fitted to properly
hold the monitor. Several individual pieces are required to
hold the monitor at the desired angle. In most cases, the
monitor is not adjustable. Care must be taken that the
monitor mount does not interfere with document camera
drawers, pullout shelves, etc. It is necessary for the
monitor to be in our shop before production can begin. |
| |
|
M-LCD Open Recessed LCD Monitor Mount |
$700 |
|
| |
|
|
|
|
|
|
Glass Covered LCD
Monitor Mount
This is a complex mount that must be hand fitted to properly
hold the monitor. Several individual pieces are required to
hold the monitor at the desired angle. In most cases, the
monitor is not adjustable. Care must be taken that the
monitor mount does not interfere with document camera
drawers, pullout shelves, etc. It is necessary for the
monitor to be in our shop before production can begin. |
| |
|
M-LCD-PG LCD Monitor Mount with 1/4”
Plexiglass |
$890 |
|
M-LCD-TG LCD Monitor Mount with 1/4” Tempered
Glass |
$990 |
|
|
|
|
|
|
Wacom™/Crestron™/Smart™ Mount
This is a surface mount for all models of Smart Sympodiums
as well as for other manufacturers of touch screens. The
screen is placed as close to the speaker as possible to make
writing on the screen more comfortable. Shown installed in a
split-top lectern. Can also be installed in slant or flat
top lecterns and desks. Mount cost does not include cost of
split top. |
| |
|
SYM-24 Touch
Screen Mount |
$230 |
|
|
|
|
|
|
Electric Monitor
Lift
Touch a button and a 10” to 17” LCD monitor rises from the
lectern, desk or table top. A fail-safe, hinged flap in the
worksurface stays below audience view when the monitor is in
the up position. Gravity closes the top so there is no pinch
point. Available in lift ranges for 10” to 15” monitors and
for 17” monitors. The lift can be contact controlled from a
separate touch panel also. |
| |
|
M-TFT-50 Electric Monitor Lift, Small |
$1,650 |
|
M-TFT-70 Electric Monitor Lift, Large |
$1,900 |
|
|
|
|
|
|
Convertible
Covered-to-Touchscreen Mount
This mount lets you switch from a glass covered LCD mount to
an open touch screen mount (Wacom, Smart, Crestron) by simply
unscrewing the glass supports and inserting a supplied floor
panel that holds the touch screen at the right angle.
|
| |
|
LCD/TOUCH Convertible
Mount |
$750 |
|
|
|
|
|
|
Large Monitor
Security Mount
Designed for VESA and rotating mount 14” to 18” control
monitors and displays, this mount can be adjusted left and
right and up and down. Teflon bearings allow for easy movement
or they can be tightened to stop movement. A one inch steel
bolt anchors the 16 gauge, powder-coated steel case to the
work surface. Standard fasteners are hex bolts with nylon
security nuts. Other fasteners may be specified. |
| |
|
MTA2000 Large Security Mount |
$570 |
|
Quantity pricing available. |
|
|
|
|
|
|
Small Monitor
Security Mount
Designed for small control monitors and displays, this mount
can be adjusted left and right and up and down. Teflon
bearings allow for easy movement or they can be Tightened to
stop movement. A 5/8” steel bolt anchors the 16 gauge powder
coated steel case to the work surface. Standard fasteners
are hex bolts with nylon security nuts. Other fasteners may
be specified. |
| |
|
MTA1000 Small
Security Mount |
$360 |
|
Quantity pricing available. |
|
|
|
|
|
|
Mount Boxes
Mount boxes can be added to any flat surface as either fixed
or loose housings for panel mount devices. Size, angle and
finish as required. |
| |
|
|
|
Custom Presentation Furniture
